Heating system part identification

[CeylonstonE9]

This is my heating system plastic parts. It wasn't on the car when I bought it so it is kind of a puzzle for me.

I found out I was missing the other side of this thing then I got it. Now Hoping I am not missing anything else.

My questions is... this half broken part belong to the heating system or not. (it may be mixed in to my parts so that is why I am asking)

Also let me know if I am missing something.

 

[Dick Steinkamp]

You may be missing a heater part....but to offset that loss you have a Chevy V8 intake manifold gasket. ...

 

[CeylonstonE9]

You may be missing a heater part....but to offset that loss you have a Chevy V8 intake manifold gasket. ...

View attachment 156295

Oh this is new... I usually find renault and peugeot stuff in my E9 parts.

 

[CeylonstonE9]

I took them out again this is the updated version without the chevy stuff but I still don't know what is that broken part. Maybe that is also chevy part.

 

[HB Chris]

Two parts upper left and one on far right are not e9. Silver upper panel looks like e3.

 

[CeylonstonE9]

Two parts upper left and one on far right are not e9. Silver upper panel looks like e3.

I think this type comes up in early 70s E9 but color is always black in E9.
My car is 1972 E9 but I don't know why this heater panel is silver with no paint on it.
Plus it has some drill holes on it too.

 

[Dick Steinkamp]

That silver panel is not an E3. Here's an E3 with AC (BTW, most E3s had wood grain where the brushed stainless is on this one). E12 maybe?

 

[Wladek]

Heater adjust panel is e3

 

[CeylonstonE9]

Heater adjust panel is e3View attachment 156400

Thank you for pointing out. Now I think I have to buy E9 heater panel. Are the other stuff suitable for E9 ?

 

[HB Chris]

You saw my reply?

 

[bluecoupe30!]

If this has not been pointed out yet, you seem to have 2 intermediate pieces. In latest photo, on left. One is correct for E9, the other, in lowest position in photo, fits E3. (it shows the openings for the hoses that channel air to the left and right sides of the dash. In the very front you have the flaps that fit inside your heater.

 

[CeylonstonE9]

If this has not been pointed out yet, you seem to have 2 intermediate pieces. In latest photo, on left. One is correct for E9, the other, in lowest position in photo, fits E3. (it shows the openings for the hoses that channel air to the left and right sides of the dash. In the very front you have the flaps that fit inside your heater.

You mean this is for E3 right ?

 

[CeylonstonE9]

Two parts upper left and one on far right are not e9. Silver upper panel looks like e3.

You mean these are not E9 right?

 

[bluecoupe30!]

View attachment 156424

You mean this is for E3 right ?

Yep. Also, heater case seems to be missing the specific clips to hold the 2 halves together. Check the DIY section here. Erik Netherlands put together a very helpful and comprehensive rebuild post. Good luck!

 

[HB Chris]

View attachment 156425

You mean these are not E9 right?

Yes

 

[eriknetherlands]

Here a link that will help you figure out some of the parts and how they work in unison.
Keep in mind that my system in the thread is a non AC version:

Thread 'DIY - Heater unit rebuild' https://e9coupe.com/forum/threads/diy-heater-unit-rebuild.38896/

 

[eriknetherlands]

Could the silver Heater control panel be 2000cs perhaps?

 

[CeylonstonE9]

Could the silver Heater control panel be 2000cs perhaps?

Maybe... these two doesn't exactly fit too. There is a gap. As Wladek said back back control panel is E3 and front panel something else... 2000cs maybe
I checked your post mine is also none A/C. I am thinking I may need a complete set now.

 

[eriknetherlands]

2000CS seems to have 4 levers as well, but not 1 at top and 3 below, but the 2000CS has two on top, and 2 below:

origin:

BMW-2000 C coupe | Joop Stolze Classic Cars

BMW - 2000 C coupe | Perfect rijdende, ZEER mooie, originele BMW 2000C coupé. Nog geheel origineel en slechts 49.000 Km

www.stolzeclassiccars.nl