72 3.0 CS 2240344 Restoration

Fun, but exhausting three days of racing at the USGP at COTA in Austin this weekend! My son came in from Chicago, and we took my Daughter's 4 YO (all cars all the the time Bennie) for practice on Friday.. Great racing included the 16-24 YO women's F1 Academy race (really good wheel to wheel racing!), the Carerra Cup, a vintage F1 car race, and the F1 GP (Antonelli was superb!)View attachment 228688


View attachment 228689

View attachment 228690
Antonelli is amazing; he may turn out to be a generational talent. How was the experience of going to Austin? Transportation, food, seats, bathrooms, etc.
 
Antonelli is amazing; he may turn out to be a generational talent. How was the experience of going to Austin? Transportation, food, seats, bathrooms, etc.
Easy! I paid for parking with our tickets. Maybe 45 mins each way from downtown Austin. We have place there so lodging was easy. My son paid a lot for a hotel, so book early for that. Bathrooms food refreshments all pretty easy. Our seats were at the turn 15 bleachers. Plan on walking a lot. Seats are expensive. 3 day pass in seats at 15 were $1k each
 
If I knew now what I knew when I was dealing with wiring last year I would probably do the same. It seemed very difficult and annoying to remove all of the wiring and yes it would have been but I’ve accessed about 80% of it anyways
The harness makes a lot of sense once you figure out what goes where
 
the real key, if you change things, is to document what you changed. i have an autocad file on mine, but since i didn't make the harness for megasquirt, that is not up to date. but all of the changes to the original wires that were documented.
 
Finally got the diff and the remaining steering parts painted today. Assembled the front sub frame (loosely), attached the steering box, painted the diff, etc. Homing in on being ready to put the suspension back on the car. Made sure I had all the right hardware, etc.

Planning to start the wiring this week.

Front subframe sort of folded up for transport. Ready to go on the car.
IMG_6922 2.jpeg


Diff painted.

IMG_6923 2.jpeg
IMG_6925 2.jpeg


Numbering on the diff. 38/11=3.454545...
IMG_6924 2.jpeg
 
Got a deal today for a scissor lift from the guy in the the next bay over from me at my shop. I think I'll give that a try. It can lift the bottom of the car about 4 feet off the ground. Because it is a scissor, the access directly under the car is a bit limited, but it's worth a try for a fraction of a 2 post lift, and it is super sturdy!
 
Finally got the diff and the remaining steering parts painted today. Assembled the front sub frame (loosely), attached the steering box, painted the diff, etc. Homing in on being ready to put the suspension back on the car. Made sure I had all the right hardware, etc.

Planning to start the wiring this week.

Front subframe sort of folded up for transport. Ready to go on the car.
View attachment 229502

Diff painted.

View attachment 229503View attachment 229505

Numbering on the diff. 38/11=3.454545...View attachment 229504
Its no wonder I get my ass kicked at all the concourse events. My steering box is a mess.
 
Its no wonder I get my ass kicked at all the concourse events. My steering box is a mess.
Took me hours of scrubbing to get the old steering box clean enough to paint. And truth be told, I did not remove the pitman arm. In a perfect world I would have done that, and powder coated it...

The beauty of taking your car completely apart is that you can renew every part before putting it back together again.. Yes, a lot of work, but the end result is super clean. The down side is that it is a PITA to put it all back together!!

Everything going back in the car is either brand new or refurbished. New hardware everywhere. Belmetric is my new best friend...
 
Last edited:
Finally got around to test fitting the latest incarnation of the Weber side draft manifolds. I had some earlier issues with getting the flanges to fit the head studs properly. I finally bought a very nice centering caliper to accurately measure the hole spacings, revised the model and had a set printed. Today I went over tot he shop and test fitted them. Flanges fit perfectly. The bores are almost perfect. I was able to match the M90 head intake "bump" to within a fraction of a mm (you can just barely feel the step at the joint). The lower edge of the port is about 1mm or less too open, as can be seen the pics below.

@e9Leveque pointed me to a place that does metal printing for a reasonable price. The place I was using wanted about $700 each in Aluminum. I can get all three from this new place for about $450.

The keen eye will notice e that these have the car name embossed on the center web. totally bespoke!

IMG_6956.jpeg
IMG_6957.jpeg
IMG_6958.jpeg
IMG_6959.jpeg
 
On low volume, limited run engine castings, especially aluminum, you often run into voids, pores, and micro flaws, etc. This allows gassing, tiny leaks, etc. which may not impact performance; but over time, you will see yellowing, discoloration, leaks. This was more common in the old days; again low volume production runs. I experienced it several times. Just Google it and you will see. It has been a common process.

You are printing this part, and I do not know if metal printing will have the same flaws of cast parts. But you are making a beautiful looking part, and this is just one more step. I am sorry...I don't want to make this complicate for you. But after almost 40 years in engine development, I can't help myself.
 
Back
Top